Turn Shatter To E-Juice

Shatter is a crystalline herbal concentrate that is made from butane extracts. If correctly handled, it can remain in a crystalline state for quite a reasonable time, especially when at room temperature, if you are to turn shatter to e-juice successfully.

Invention about the vape technology, especially the cartridge, has brought about an ordinance to spare smokers the hustle of carrying rolling papers, pipe, and enormous bongs.

If you care about your health too, it is to keep your lungs healthy away from the chemical components.

Rolling papers incur so many chemical processes to be availed at your disposal.

This substance is normally smoked upon value addition, such as converting it to flavoring and injecting it into your vape pen for the best results.

The concentrate is normally acquired from leading shops, such as eBay.

So what is the process of converting shatter to vape juice?

For this process to occur, one needs to activate the shatter basically by heating it indirectly. This is not rocket science. 

If you are crafty enough, you can process it by the use of a microwave or use a dual evaporator, which is so easy and safe.

Use of a dual evaporator 

What you need;

  • A syringe used to load vape cartridge 
  • A small glass 
  • Metal holder 
  • 1 to 2 grams of shatter.

 A bigger jar that is used to heat water used to vaporize shatter.

  • Add water to waters boiled to 80 degrees Celsius. You need to have a water meter to get definite results, especially when you are a perfectionist.

However, you need not worry if you dominative one since you can kit it out should the water be warm enough.

  • The second step is adding your chatter into a blending glass.

It needs to be clear so that you keep on monitoring the process inside the gas for a maximum of five minutes because with this time it completely softens.

  • On the next step, an EJ blend is added into the liquefied shatter at the ratio of 1 ml Ecblend to 1 gram shatter.

The process of blending the mixture should take at least five minutes.

  • The shatter should then be evacuated through the use of a syringe, and permit the blend to take place for up to 15 minutes.

The use of an oven.

What you need;

  • 1 to 2 grams of shatter, depending on the size of your vape pen. You’re supposed to source it from your local stores.
  • Ecblend (THC extract vegetable  glycerin, and polypropylene glycol  )
  • A syringe and, of course, your vape pen.
  • A metallic holding tool to help you hold the glass jar.
  • Terpenes are used to add flavor to your vape for better results.
  • For those who need super quick results, a faster method can be induced.

You need to be very careful because this is dangerous, due to its nature of interacting directly with heat.

  • First, you need to add a gram of shatter to clear glass. Be careful about the proportionality.
  • Next, you add a millimeter of Ejblend to the shatter.
  • After this, you have to place it inside the microwave and allow it to blend heat for 10 minutes.
  • After that, you should get the blend out of the microwave and get to mix it fast while extracting undissolved debris from the vape juice.
  • Use a syringe to extract the vape juice that is supposed to dows for up to 15 minutes; subsequently, add it to your vape pen.


With the two methods above, an outdoor vaping experience can be so charming at the disposal of a vape pen.

All these are hacks that require know-how if you are not sure of any step to consult a person who has done this before so that you don’t mess up in the process to turn shatter into e-juice.

Equally, for consumers of medical marijuana, this can spare you the hassle of lighters and have your THC at the disposal of your fingertips.

Keep in mind that your lungs need to be healthy! 

Consumption of vape needs to be proper to keep one’s lungs healthy. Consumption of almost 5 mg vape can be enough for a day. Doctors’ prescriptions also need to be followed when it comes to conditional Medical prescriptions.

Leave a Reply

  • (will not be published)

XHTML: You can use these tags: <a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <cite> <code> <del datetime=""> <em> <i> <q cite=""> <s> <strike> <strong>